README
¶
Edison
The Intel Joule is a WiFi and Bluetooth enabled development platform for the Internet of Things.
For more info about the Intel Joule platform go to:
How to Install
Please refer to the main README.md
Setting up your Intel Joule
Everything you need to get started with the Joule is in the Intel Getting Started Guide located at:
https://intel.com/joule/getstarted
Don't forget to configure your Joule's WiFi connection and update your Joule to the latest firmware image. Gobot has been tested using the reference OS based on Ostro.
How To Use
package main
import (
"time"
"gobot.io/x/gobot/v2"
"gobot.io/x/gobot/v2/drivers/gpio"
"gobot.io/x/gobot/v2/platforms/intel-iot/joule"
)
func main() {
e := joule.NewAdaptor()
led := gpio.NewLedDriver(e, "GP103")
work := func() {
gobot.Every(1*time.Second, func() {
if err := led.Toggle(); err != nil {
fmt.Println(err)
}
})
}
robot := gobot.NewRobot("blinkBot",
[]gobot.Connection{e},
[]gobot.Device{led},
work,
)
if err := robot.Start(); err != nil {
panic(err)
}
}
You can read the full API documentation online.
How to Connect
Compiling
Compile your Gobot program on your workstation like this:
GOARCH=386 GOOS=linux go build joule_blink.go
Once you have compiled your code, you can you can upload your program and execute it on the Intel Joule from your workstation
using the scp and ssh commands like this:
scp joule_blink root@<IP of your device>:/home/root/
ssh -t root@<IP of your device> "./joule_blink"
At this point you should see one of the onboard LEDs blinking. Press control + c to exit.
To update the program after you made a change, you will need to scp it over once again and start it from the command line (via screen).
Pin Mapping
The Gobot pin mapping for the Intel Joule uses a naming system based on how the pins are labeled on the board itself.
There are 2 jumpers on the Joule expansion board, labeled "J12" and "J13". There are 2 rows of pins on each jumper, labeled from 1 to 40. So to use the 26th pin of jumper J12, you use pin name "J12_26".
In addition, there are pins that control the build-in LEDs (pins GP100 thru GP103) as used in the example above.
The i2c interfaces on the Intel Joule developer kit board require that you terminate the SDA & SCL lines using 2 10K resistors pulled up to the voltage used for the i2c device, for example 5V.
Documentation
¶
Overview ¶
Package joule contains the Gobot adaptor for the Intel Joule.
For further information refer to intel-iot README: https://github.com/hybridgroup/gobot/blob/release/platforms/intel-iot/joule/README.md
Index ¶
Constants ¶
This section is empty.
Variables ¶
This section is empty.
Functions ¶
This section is empty.
Types ¶
type Adaptor ¶
type Adaptor struct {
*adaptors.DigitalPinsAdaptor
*adaptors.PWMPinsAdaptor
*adaptors.I2cBusAdaptor
// contains filtered or unexported fields
}
Adaptor represents an Intel Joule
func NewAdaptor ¶
func NewAdaptor(opts ...interface{}) *Adaptor
NewAdaptor returns a new Joule Adaptor
Optional parameters:
adaptors.WithGpiodAccess(): use character device gpiod driver instead of sysfs adaptors.WithSpiGpioAccess(sclk, ncs, sdo, sdi): use GPIO's instead of /dev/spidev#.# Optional parameters for PWM, see [adaptors.NewPWMPinsAdaptor]
Source Files