edison

README

Edison

The Intel Edison is a wifi and Bluetooth® enabled devolopment platform for the Internet of Things. It packs a robust set of features into its small size and supports a broad spectrum of I/O and software support.

For more info about the Edison platform click here.

How to Install (using Go 1.5+)

Install Go from source or use an official distribution.

Then you must install the appropriate Go packages

Setting up your Intel Edison

Everything you need to get started with the Edison is in the Intel Getting Started Guide:

https://software.intel.com/en-us/iot/library/edison-getting-started

Don't forget to configure your Edison's wifi connection and flash your Edison with the latest firmware image!

The recommended way to connect to your device is via wifi, for that follow the directions here:

https://software.intel.com/en-us/connecting-your-intel-edison-board-using-wifi

If you don't have a wifi network available, the Intel documentation explains how to use another connection type, but note that this guide assumes you are using wifi connection.

You can obtain the IP address of your Edison, by running the floowing command:

ip addr show | grep inet

Don't forget to setup the a password for the device otherwise you won't be able to connect using SSH. From within the screen session, run the following command:

configure_edison --password

Note that you MUST setup a password otherwise SSH won't be enabled. If later on you aren't able to scp to the device, try to reset the password. This password will obviously be needed next time you connect to your device.

Example program

Save the following code into a file called main.go.

package main

import (
	"time"

	"gobot.io/x/gobot"
	"gobot.io/x/gobot/drivers/gpio"
	"gobot.io/x/gobot/platforms/intel-iot/edison"
)

func main() {
	e := edison.NewAdaptor()
	led := gpio.NewLedDriver(e, "13")

	// Uncomment the line below if you are using a Sparkfun
	// Edison board with the GPIO block
	// e.SetBoard("sparkfun")

	work := func() {
		gobot.Every(1*time.Second, func() {
			led.Toggle()
		})
	}

	robot := gobot.NewRobot("blinkBot",
		[]gobot.Connection{e},
		[]gobot.Device{led},
		work,
	)

	robot.Start()
}

You can read the full API documentation online.

Cross compiling for the Intel Edison

Compile your Gobot program run the following command using the command line from the directory where you have your main.go file:

$ GOARCH=386 GOOS=linux go build .

Then you can simply upload your program over the network from your host computer to the Edison

$ scp main root@<IP of your device>:/home/root/blink

and execute it on your Edison (use screen to connect, see the Intel setup steps if you don't recall how to connect)

$ ./blink

At this point you should see the onboard LED blinking. Press control + c to exit.

To update the program after you made a change, you will need to scp it over once again and start it from the command line (via screen).

License

Copyright (c) 2014-2016 The Hybrid Group. Licensed under the Apache 2.0 license.

Documentation

Overview

Package edison contains the Gobot adaptor for the Intel Edison.

For further information refer to intel-iot README: https://gobot.io/x/gobot/blob/master/platforms/intel-iot/edison/README.md

Index

• type Adaptor
  • func NewAdaptor() *Adaptor
  • func (e *Adaptor) AnalogRead(pin string) (val int, err error)
  • func (e *Adaptor) Board() string
  • func (e *Adaptor) Connect() (err error)
  • func (e *Adaptor) DigitalRead(pin string) (i int, err error)
  • func (e *Adaptor) DigitalWrite(pin string, val byte) (err error)
  • func (e *Adaptor) Finalize() (err error)
  • func (e *Adaptor) I2cRead(address int, size int) (data []byte, err error)
  • func (e *Adaptor) I2cStart(address int) (err error)
  • func (e *Adaptor) I2cWrite(address int, data []byte) (err error)
  • func (e *Adaptor) Name() string
  • func (e *Adaptor) PwmWrite(pin string, val byte) (err error)
  • func (e *Adaptor) SetBoard(n string)
  • func (e *Adaptor) SetName(n string)

Types

type Adaptor

type Adaptor struct {
	// contains filtered or unexported fields
}

Adaptor represents a Gobot Adaptor for an Intel Edison

func NewAdaptor

func NewAdaptor() *Adaptor

NewAdaptor returns a new Edison Adaptor

func (*Adaptor) AnalogRead

func (e *Adaptor) AnalogRead(pin string) (val int, err error)

AnalogRead returns value from analog reading of specified pin

func (*Adaptor) Board

func (e *Adaptor) Board() string

Board returns the Adaptors board name

func (*Adaptor) Connect

func (e *Adaptor) Connect() (err error)

Connect initializes the Edison for use with the Arduino beakout board

func (*Adaptor) DigitalRead

func (e *Adaptor) DigitalRead(pin string) (i int, err error)

DigitalRead reads digital value from pin

func (*Adaptor) DigitalWrite

func (e *Adaptor) DigitalWrite(pin string, val byte) (err error)

DigitalWrite writes a value to the pin. Acceptable values are 1 or 0.

func (*Adaptor) Finalize

func (e *Adaptor) Finalize() (err error)

Finalize releases all i2c devices and exported analog, digital, pwm pins.

func (*Adaptor) I2cRead

func (e *Adaptor) I2cRead(address int, size int) (data []byte, err error)

I2cRead returns size bytes from the i2c device

func (*Adaptor) I2cStart

func (e *Adaptor) I2cStart(address int) (err error)

I2cStart initializes i2c device for addresss

func (*Adaptor) I2cWrite

func (e *Adaptor) I2cWrite(address int, data []byte) (err error)

I2cWrite writes data to i2c device

func (*Adaptor) Name

func (e *Adaptor) Name() string

Name returns the Adaptors name

func (*Adaptor) PwmWrite

func (e *Adaptor) PwmWrite(pin string, val byte) (err error)

PwmWrite writes the 0-254 value to the specified pin

func (*Adaptor) SetBoard

func (e *Adaptor) SetBoard(n string)

SetBoard sets the Adaptors name

func (*Adaptor) SetName

func (e *Adaptor) SetName(n string)

SetName sets the Adaptors name