spi

package
v0.7.0 Latest Latest
Warning

This package is not in the latest version of its module.

 Go to latest Published: Nov 15, 2020 License: BSD-3-Clause Imports: 12 Imported by: 0

Documentation

Overview

Package spi provides access to the registers of the SPI peripheral. It also provides a driver that implements synchronous I/O.

Index

Constants

View Source 
const (
	CPHA0  = Config(0)        // Sample on first edge.
	CPHA1  = Config(spi.CPHA) // Sample on second edge.
	CPOL0  = Config(0)        // Clock idle state is 0.
	CPOL1  = Config(spi.CPOL) // Clock idle state is 1.
	Slave  = Config(0)        // Slave mode.
	Master = Config(spi.MSTR) // Master mode.

	BR2   = Config(0)            // Baud rate = PCLK/2
	BR4   = Config(1 << spi.BRn) // Baud rate = PCLK/4.
	BR8   = Config(2 << spi.BRn) // Baud rate = PCLK/8.
	BR16  = Config(3 << spi.BRn) // Baud rate = PCLK/16.
	BR32  = Config(4 << spi.BRn) // Baud rate = PCLK/32.
	BR64  = Config(5 << spi.BRn) // Baud rate = PCLK/64.
	BR128 = Config(6 << spi.BRn) // Baud rate = PCLK/128.
	BR256 = Config(7 << spi.BRn) // Baud rate = PCLK/256.

	MSBF = Config(0)            // Most significant bit first.
	LSBF = Config(spi.LSBFIRST) // Least significant bit first.

	HardSS = Config(0)       // Hardware slave select.
	SoftSS = Config(spi.SSM) // Software slave select (use ISSLow, ISSHigh).

	ISSLow  = Config(0)       // Set NSS internally to low (used with SoftSS).
	ISSHigh = Config(spi.SSI) // Set NSS internally to high (used with SoftSS).

	SSInp = Config(0)              // Set NSS as input (used with HardSS).
	SSOut = Config(spi.SSOE << 16) // set NSS as output (used with HardSS).

	ThreeWire = Config(0)            // Three-wire mode (SCK, MOSI, MISO).
	TwoWire   = Config(spi.BIDIMODE) // Two-wire mode (SCK, MOSI/MISO).

	TxRx   = Config(0)          // Three-wire transimt and receive.
	RxOnly = Config(spi.RXONLY) // Three-wire receive only.

	Rx = Config(0)          // Two-wire receive-only.
	Tx = Config(spi.BIDIOE) // Two-wire transmit-only.

)
View Source 
const (
	Err        = Event(1)             // Some hardware error occurs.
	RxNotEmpty = Event(spi.RXNE) << 1 // Receive buffer not empty.
	TxEmpty    = Event(spi.TXE) << 1  // Transmit buffer empty.
	Busy       = Event(spi.BSY) << 1  // Periph is busy (not a real event).

)
View Source 
const (
	ErrCRC     = Error(spi.CRCERR >> 3)
	ErrMode    = Error(spi.MODF >> 3)
	ErrOverrun = Error(spi.OVR >> 3)
)

Variables

This section is empty.

Functions

func UsePinMaster added in v0.3.0 

func UsePinMaster(pin gpio.Pin, af gpio.AltFunc, sig Signal)

UsePinMaster is a helper function that can be used to configure GPIO pins as required by SPI master device.

func UsePinSlave added in v0.3.0 

func UsePinSlave(pin gpio.Pin, af gpio.AltFunc, sig Signal)

UsePinSlave is a helper function that can be used to configure GPIO pins as required by SPI slave device.

Types

type Config added in v0.2.1 

type Config uint32

type Driver 

type Driver struct {
	// contains filtered or unexported fields
}

func NewDriver 

func NewDriver(p *Periph, rxdma, txdma dma.Channel) *Driver

NewDriver provides convenient way to create heap allocated Driver struct.

func (*Driver) DMAISR 

func (d *Driver) DMAISR(ch dma.Channel)

func (*Driver) Disable added in v0.2.1 

func (d *Driver) Disable()

Disable calls d.Periph().Disable().

func (*Driver) Enable added in v0.2.1 

func (d *Driver) Enable()

Enable calls d.Periph().Enable().

func (*Driver) Err 

func (d *Driver) Err(clear bool) error

Err returns value of internal error variable and clears it if clear is true.

func (*Driver) ISR 

func (d *Driver) ISR()

func (*Driver) Periph 

func (d *Driver) Periph() *Periph

Periph returns the SPI peripheral used by Driver.

func (*Driver) RepeatByte 

func (d *Driver) RepeatByte(b byte, n int)

func (*Driver) RepeatWord16 

func (d *Driver) RepeatWord16(w uint16, n int)

func (*Driver) RxDMA 

func (d *Driver) RxDMA() dma.Channel

func (*Driver) SetBaudrate added in v0.2.1 

func (d *Driver) SetBaudrate(baudrate int)

SetBaudrate calls d.Periph().SetBaudrate(baudrate).

func (*Driver) SetTimeout added in v0.3.0 

func (d *Driver) SetTimeout(timeout time.Duration)

func (*Driver) SetWordSize added in v0.2.1 

func (d *Driver) SetWordSize(size int)

SetWordSize calls d.Periph().SetWordSize(size).

func (*Driver) Setup added in v0.2.1 

func (d *Driver) Setup(conf Config, baudrate int)

Setup enables clock source, resets peripheral, then calls d.Periph().SetConfig(conf, baudrate) to configure it.

func (*Driver) TwoWireSetRx added in v0.2.1 

func (d *Driver) TwoWireSetRx()

TwoWireSetRx can be used in two-wire mode to set data direction to recevie.

func (*Driver) TwoWireSetTx added in v0.2.1 

func (d *Driver) TwoWireSetTx()

TwoWireSetRx can be used in two-wire mode to set data direction to transimit.

func (*Driver) TxDMA 

func (d *Driver) TxDMA() dma.Channel

func (*Driver) WriteRead 

func (d *Driver) WriteRead(out, in []byte) int

func (*Driver) WriteRead16 

func (d *Driver) WriteRead16(out, in []uint16) int

func (*Driver) WriteReadByte 

func (d *Driver) WriteReadByte(b byte) byte

WriteReadByte writes and reads byte.

func (*Driver) WriteReadMany 

func (d *Driver) WriteReadMany(oi ...[]byte) int

func (*Driver) WriteReadMany16 

func (d *Driver) WriteReadMany16(oi ...[]uint16) int

func (*Driver) WriteReadWord16 

func (d *Driver) WriteReadWord16(w uint16) uint16

WriteReadWord16 writes and reads 16-bit word.

func (*Driver) WriteStringRead 

func (d *Driver) WriteStringRead(out string, in []byte) int

type DriverError 

type DriverError byte
const ErrTimeout DriverError = 1

func (DriverError) Error 

func (e DriverError) Error() string

type Error 

type Error byte

Error is a bitfield that encodes possible peripheral errors.

func (Error) Error 

func (e Error) Error() string

type Event 

type Event uint16

Event is a bitfield that encodes possible peripheral events.

type Periph 

type Periph struct {
	// contains filtered or unexported fields
}

Periph represents SPI peripheral.

func (*Periph) BR 

func (p *Periph) BR(baudrate int) Config

BR calculates the baud rate bits of configuration. BR guarantees that the returned bits corresponds to the value closest to but not greater than baudrate.

func (*Periph) Baudrate 

func (p *Periph) Baudrate() int

Baudrate returns the currently configured baudrate.

func (*Periph) Bus 

func (p *Periph) Bus() bus.Bus

Bus returns a bus to which p is connected to.

func (*Periph) Config added in v0.2.1 

func (p *Periph) Config() Config

Config returns the current p's configuration.

func (*Periph) Disable 

func (p *Periph) Disable()

Disable disables p.

func (*Periph) DisableClock 

func (p *Periph) DisableClock()

DisableClock disables clock for p.

func (*Periph) DisableDMA 

func (p *Periph) DisableDMA(e Event)

DisableDMA disables generating of DMA requests by events e.

func (*Periph) DisableIRQ 

func (p *Periph) DisableIRQ(e Event)

DisableIRQ disables generating of IRQ by events e.

func (*Periph) EditConfig added in v0.2.3 

func (p *Periph) EditConfig(from, to Config)

EditConfig changes configuration.

func (*Periph) Enable 

func (p *Periph) Enable()

Enable enables p.

func (*Periph) EnableClock 

func (p *Periph) EnableClock(lp bool)

EnableClock enables clock for p. lp determines whether the clock remains on in low power (sleep) mode.

func (*Periph) EnableDMA 

func (p *Periph) EnableDMA(e Event)

EnableDMA enables generating of DMA requests by events e.

func (*Periph) EnableIRQ 

func (p *Periph) EnableIRQ(e Event)

EnableIRQ enables generating of IRQ by events e.

func (*Periph) Enabled 

func (p *Periph) Enabled() bool

Enabled reports whether p is enabled.

func (*Periph) LoadByte 

func (p *Periph) LoadByte() byte

LoadByte loads a byte from the data register. Use it only when 8-bit frame is configured.

func (*Periph) LoadWord16 

func (p *Periph) LoadWord16() uint16

LoadWord16 loads a 16-bit word from the data register. Use it only when 16-bit word or data packing is configured.

func (*Periph) Reset 

func (p *Periph) Reset()

Reset resets p.

func (*Periph) SetBaudrate added in v0.2.1 

func (p *Periph) SetBaudrate(baudrate int)

SetBaudrate sets the baudrate (p must be disabled).

func (*Periph) SetConfig added in v0.2.1 

func (p *Periph) SetConfig(conf Config, baudrate int)

SetConfig configures p (p must be disabled). If baudrate > 0 it replaces the BR bits in conf with the ones calculated from baudrate.

func (*Periph) SetWordSize 

func (p *Periph) SetWordSize(size int)

SetWordSize sets size of data word. All families support 8 and 16-bit words, F0, F3, L4 supports 4 to 16-bit. Some families require disabled peripheral before use this function. SetWordSize is mandatory for F0, F3, L4 because the default reset configuration does not work.

func (*Periph) Status 

func (p *Periph) Status() (Event, Error)

Status return current status of p.

func (*Periph) StoreByte 

func (p *Periph) StoreByte(v byte)

StoreByte stores a byte to the data register. Use it only when 8-bit frame is configured.

func (*Periph) StoreWord16 

func (p *Periph) StoreWord16(v uint16)

StoreWord16 stores a 16-bit word to the data register. Use it only when 16-bit word or data packing is configured.

func (*Periph) WordSize 

func (p *Periph) WordSize() int

WordSize return currently used word size.

type Signal added in v0.3.0 

type Signal uint8
const (
	SCK Signal = iota
	MOSI
	MISO
	NSS
)

Source Files

View all Source files

Directories

Path Synopsis

Jump to

Keyboard shortcuts

? : This menu
/ : Search site
f or F : Jump to
y or Y : Canonical URL
go.dev uses cookies from Google to deliver and enhance the quality of its services and to analyze traffic. Learn more.