knx-exporter

README

KNX Prometheus Exporter

The KNX Prometheus Exporter is a small bridge to export values measured by KNX sensors to Prometheus. It takes the values either from cyclic sent GroupValueWrite telegrams and can request values itself using GroupValueRead telegrams.

Installing

macOS

Using brew tap:

brew tap chr-fritz/tap
brew install chr-fritz/tap/knx-exporter

Docker

docker pull quay.io/chrfritz/knx-exporter

Other

Download the latest release and place it in your $PATH.

Usage

Converting the ETS 5 Group Export to a configuration

The KNX Prometheus Exporter will only export the values from configured group addresses. A good starting point is to export the group addresses from ETS 5 into the XML format and convert them.

Please refer the KNX Documentation "Group Address & Export" for more information about how to export the group addresses to XML.

With the exported group addresses you can call the knx-exporter and convert them:

knx-exporter convertGA [SOURCE] [TARGET]

You must replace [SOURCE] with the path to your group address export file. [TARGET] is the path where the converted configuration should be stored.

Preparing the configuration

Converting the group addresses is a good starting point for preparing the actual configuration. The simplest fully configuration will look like this:

Connection:
  Type: "Tunnel"
  Endpoint: "192.168.1.15:3671"
  PhysicalAddress: 2.0.1
MetricsPrefix: knx_
AddressConfigs:
  0/0/1:
    Name: dummy_metric
    DPT: 1.*
    Export: true
    MetricType: "counter"
    ReadActive: true
    MaxAge: 10m
    Comment: dummy comment

In the next sections we will describe the meanings for every statement.

The Connection section

The Connection section contains all settings about how to connect to your KNX system and how the KNX Prometheus Exporter will identify itself within it. It has three properties:

• Type This defines the connection type to your KNX system. It can be either Router or Tunnel.
• Endpoint This defines the ip address or hostname including the port to where the KNX Prometheus Exporter should open the connection. In case of you are using Router in Type the default might be 224.0.23.12:3671.
• PhysicalAddress This defines the physical address how the KNX Prometheus Exporter will identify itself within your KNX address.

The MetricsPrefix

The MetricsPrefix defines a single string that will be added to all your exported metrics. The format must be compliant with the prometheus metrics names.

The AddressConfigs section

The AddressConfigs section defines all the information about the group addresses which should be exported to prometheus. It contains the following structure for every exported group address.

  0/0/1:
    Name: dummy_metric
    DPT: 1.*
    Export: true
    MetricType: "counter"
    ReadActive: true
    MaxAge: 10m
    Comment: dummy comment

The first line 0/0/1 defines the group address which should be exported. It can be written in all three valid forms:

• Two layers: 0/1
• Three layers: 0/0/1
• Free structure 123

You can find more information about the formatting of group addresses here: cemi@v0.0 NewGroupAddrString

Next it defines the actual information for a single group address:

• Name is the short name of the exported metric. The format must be compliant with the prometheus metrics names.
• DPT The knx data point type. This defines how the KNX Prometheus Exporter will interpret the payload of received telegrams. All available data point types can be found here: knx dpt
• Export Can be either true or false. Allows to disable exporting the group address as value.
• MetricType defines the type of the exported metric. Can be either counter or gauge. See Prometheus documentation counter vs. gauge for more information about it.
• ReadActive can either be true or false. If set to true the KNX Prometheus Exporter will send a GroupValueRead telegram to the group address to active ask for a new value if the last received value is older than MaxAge.
• MaxAge defines the maximum age of a value until the KNX Prometheus Exporter will send a GroupValueRead telegram to active request a new value for the group address. This setting will be ignored if ReadActive is set to false.
• Comment a short comment for the group address. Will be also exported as comment within the prometheus metrics.

Running the exporter

To run the metrics export just run the following command:

knx-exporter run -f [CONFIG-FIlE]

You must replace [CONFIG-FILE] with the path to your configuration file that you prepared in the previous step. After starting the exporter you can open http://localhost:8080/metrics to view the exported metrics.

Exported metrics

Beside exported metrics from KNX group addresses it exports some additional metrics. This metrics can be grouped into three groups:

1. KNX Message Metrics: Three counter metrics which counts the number of
   • received messages knx_messages{direction="received",processed="false"}
   • processed received messages knx_messages{direction="received",processed="true"} and
   • sent messages knx_messages{direction="sent",processed="true"}.
2. HTTP Metrics: Counts the processed number of successfully and failed http requests. All metrics starts with promhttp_.
3. GoLang Metrics: These are metrics which indicates some health information about memory, cpu usage, threads and other GoLang internal information.

Health Check Endpoints

The KNX Prometheus Exporter provides endpoints for liveness and readiness checks like they were recommended in enviroments like Kubernetes. They are reachable under /live and /ready. With /live?full=1 and /ready?full=1 they also print the status of every single check.

Contributing

1. Fork it
2. Download your fork to your PC (git clone https://github.com/your_username/knx-exporter && cd knx-exporter)
3. Create your feature branch (git checkout -b my-new-feature)
4. Make changes and add them (git add .)
5. Commit your changes (git commit -m 'Add some feature')
6. Push to the branch (git push origin my-new-feature)
7. Create new pull request

License

The KNX Exporter is released under the Apache 2.0 license. See LICENSE

Maintainer

Christian Fritz (@chrfritz)